Signed-off-by: unknown <crnf@.(none)>

oozebane.csv

+Format is tab separated oozebane settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Oozebane	
+Activate Oozebane	False
+After Startup Distance (millimeters):	1.2
+Early Shutdown Distance (millimeters):	1.2
+Early Startup Distance Constant (millimeters):	20.0
+Early Startup Maximum Distance (millimeters):	1.2
+First Early Startup Distance (millimeters):	25.0
+Minimum Distance for Early Startup (millimeters):	0.0
+Minimum Distance for Early Shutdown (millimeters):	0.0
+Slowdown Startup Steps (positive integer):	3

polyfile.csv

+Format is tab separated polyfile settings.
+_Name                          	Value
+WindowPosition	700+0
+Execute All Unmodified Files in a Directory	False
+Execute File	True

preface.csv

+Format is tab separated preface settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Preface	
+Meta:	
+Name of End File:	end.gcode
+Name of Start File:	start.gcode
+Set Positioning to Absolute	True
+Set Units to Millimeters	True
+Start at Home	False
+Turn Extruder Off at Shut Down	True
+Turn Extruder Off at Start Up	True

raft.csv

+Format is tab separated raft settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Raft	
+Activate Raft	True
+Add Raft, Elevate Nozzle, Orbit:	True
+Base Feed Rate Multiplier (ratio):	1.1
+Base Flow Rate Multiplier (ratio):	1.1
+Base Infill Density (ratio):	0.7
+Base Layer Thickness over Layer Thickness:	2.0
+Base Layers (integer):	0
+Base Nozzle Lift over Base Layer Thickness (ratio):	0.4
+Initial Circling:	False
+Infill Overhang over Extrusion Width (ratio):	0.05
+Interface Feed Rate Multiplier (ratio):	1.1
+Interface Flow Rate Multiplier (ratio):	1.1
+Interface Infill Density (ratio):	0.7
+Interface Layer Thickness over Layer Thickness:	1.0
+Interface Layers (integer):	0
+Interface Nozzle Lift over Interface Layer Thickness (ratio):	0.45
+Name of Support End File:	support_end.gcode
+Name of Support Start File:	support_start.gcode
+Object First Layer Feed Rate Infill Multiplier (ratio):	0.4
+Object First Layer Feed Rate Perimeter Multiplier (ratio):	0.4
+Object First Layer Flow Rate Infill Multiplier (ratio):	0.4
+Object First Layer Flow Rate Perimeter Multiplier (ratio):	0.4
+Operating Nozzle Lift over Layer Thickness (ratio):	0.5
+Raft Additional Margin over Length (%):	1.0
+Raft Margin (mm):	3.0
+Support Cross Hatch	False
+Support Flow Rate over Operating Flow Rate (ratio):	1.0
+Support Gap over Perimeter Extrusion Width (ratio):	1.0
+None	True
+Empty Layers Only	False
+Everywhere	False
+Exterior Only	False
+Support Minimum Angle (degrees):	60.0

scale.csv

+Format is tab separated scale settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Scale	
+Activate Scale:	False
+XY Plane Scale (ratio):	1.0
+Z Axis Scale (ratio):	0.2
+SVG Viewer:	webbrowser

skeinforge.csv

+Format is tab separated skeinforge settings.
+_Name                          	Value
+WindowPosition	600+7
+Open File for Skeinforge	C:/Users/crnf/Desktop/printbed_assy_orca_sm01.stl
+analyze	False
+craft	True
+help	False
+meta	False
+profile	False

skeinforge_analyze.csv

+Format is tab separated skeinforge analyze settings.
+_Name                          	Value
+WindowPosition	600+0
+Open File for Analyze	/home/ands/Entwicklung/3Dprinter/skeinforge_shared/40_reprap_python_beanshell/skeinforge_application/test.stl
+comment	False
+interpret	False
+skeiniso	False
+skeinlayer	True
+statistic	False
+vectorwrite	False

skeinforge_craft.csv

+Format is tab separated skeinforge craft settings.
+_Name                          	Value
+WindowPosition	0+30
+Open File for Craft	C:/Users/crnf/Desktop/portal cardreader bottom.stl
+bottom	False
+carve	False
+chamber	False
+chop	False
+cleave	False
+clip	False
+coil	False
+comb	False
+cool	False
+dimension	False
+drill	False
+export	False
+feed	False
+fill	False
+fillet	False
+flow	False
+home	False
+hop	False
+inset	False
+jitter	False
+lash	False
+lift	False
+limit	False
+mill	False
+multiply	True
+oozebane	False
+outset	False
+preface	False
+raft	False
+scale	False
+skirt	False
+speed	False
+splodge	False
+stretch	False
+temperature	False
+tower	False
+unpause	False
+whittle	False
+widen	False
+wipe	False

skeinforge_help.csv

+Format is tab separated skeinforge help settings.
+_Name                          	Value
+WindowPosition	600+0
+Wiki Manual Primary	True

skeinforge_meta.csv

+Format is tab separated skeinforge meta settings.
+_Name                          	Value
+WindowPosition	600+0
+description	False
+polyfile	True

skeiniso.csv

+Format is tab separated skeiniso settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Skeiniso	/home/ands/Entwicklung/3Dprinter/skeinforge_shared/40_reprap_python_beanshell/skeinforge_application/test.stl
+Activate Skeiniso	True
+Frame List
+Animation Line Quickening (ratio):	1.0
+Animation Slide Show Rate (layers/second):	2.0
+Axis Rulings	True
+Band Height (layers):	5
+Bottom Band Brightness (ratio):	0.7
+Bottom Layer Brightness (ratio):	1.0
+From the Bottom	False
+From the Top	True
+Draw Arrows	False
+Go Around Extruder Off Travel	False
+Layer (index):	2
+Layer Extra Span (integer):	912345678
+Line (index):	450
+Display Line	True
+View Move	False
+View Rotate	False
+Number of Fill Bottom Layers (integer):	1
+Number of Fill Top Layers (integer):	1
+Scale (pixels per millimeter):	7.5
+Screen Horizontal Inset (pixels):	375
+Screen Vertical Inset (pixels):	361
+Show Gcode	True
+Viewpoint Latitude (degrees):	15.0
+Viewpoint Longitude (degrees):	210.0
+Width of Axis Negative Side (pixels):	2
+Width of Axis Positive Side (pixels):	6
+Width of Fill Bottom Thread (pixels):	2
+Width of Fill Top Thread (pixels):	2
+Width of Infill Thread (pixels):	1
+Width of Loop Thread (pixels):	2
+Width of Perimeter Inside Thread (pixels):	8
+Width of Perimeter Outside Thread (pixels):	8
+Width of Raft Thread (pixels):	1
+Width of Selection Thread (pixels):	6
+Width of Travel Thread (pixels):	0

skeinlayer.csv

+Format is tab separated skeinlayer settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Skeinlayer	
+Activate Skeinlayer	True
+Frame List
+Animation Line Quickening (ratio):	1.0
+Animation Slide Show Rate (layers/second):	2.0
+Draw Arrows	True
+Go Around Extruder Off Travel	False
+Layer (index):	3
+Layer Extra Span (integer):	0
+Line (index):	871
+Display Line	True
+View Move	False
+Scale (pixels per millimeter):	7.5
+Screen Horizontal Inset (pixels):	403
+Screen Vertical Inset (pixels):	303
+Show Gcode	True
+Show Position	True
+Width of Extrusion Thread (pixels):	3
+Width of Selection Thread (pixels):	6
+Width of Travel Thread (pixels):	1

skin.csv

+Format is tab separated skin settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Skin	
+Activate Skin	False
+Half Width Perimeter	True
+Hop When Extruding Infill	False
+Layers From (index):	1

skirt.csv

+Format is tab separated skirt settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Skirt	
+Activate Skirt:	False
+Convex:	True
+Gap over Perimeter Width (ratio):	1.0
+Layers To (index):	1

speed.csv

+Format is tab separated speed settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Speed	
+Activate Speed:	True
+Add Flow Rate:	True
+Bridge Feed Rate Multiplier (ratio):	1.0
+Bridge Flow Rate Multiplier (ratio):	1.0
+Duty Cyle at Beginning (portion):	1.0
+Duty Cyle at Ending (portion):	0.0
+Feed Rate (mm/s):	50.0
+Flow Rate Setting (float):	50.0
+Orbital Feed Rate over Operating Feed Rate (ratio):	0.5
+Perimeter Feed Rate over Operating Feed Rate (ratio):	1.0
+Perimeter Flow Rate over Operating Flow Rate (ratio):	1.0
+Travel Feed Rate (mm/s):	100.0

splodge.csv

+Format is tab separated splodge settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Splodge	
+Activate Splodge	False
+Initial Lift over Extra Thickness (ratio):	1.0
+Initial Splodge Feed Rate (mm/s):	1.0
+Initial Splodge Quantity Length (millimeters):	30.0
+Operating Lift over Extra Thickness (ratio):	1.0
+Operating Splodge Feed Rate (mm/s):	1.0
+Operating Splodge Quantity Length (millimeters):	1.0

statistic.csv

+Format is tab separated statistic settings.
+Name                          	Value
+WindowPosition	700+0
+Activate Statistic	True
+Machine Time ($/hour):	1.0
+Material ($/kg):	10.0
+Density (kg/m3):	930.0
+Extrusion Diameter over Thickness (ratio):	1.25
+Open File to Generate Statistics for	
+Print Statistics	True
+Save Statistics	False

stretch.csv

+Format is tab separated stretch settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Stretch	
+Activate Stretch	False
+Cross Limit Distance Over Perimeter Width (ratio):	5.0
+Loop Stretch Over Perimeter Width (ratio):	0.11
+Path Stretch Over Perimeter Width (ratio):	0.0
+Perimeter Inside Stretch Over Perimeter Width (ratio):	0.32
+Perimeter Outside Stretch Over Perimeter Width (ratio):	0.1
+Stretch From Distance Over Perimeter Width (ratio):	2.0

temperature.csv

+Format is tab separated temperature settings.
+_Name                          	Value
+WindowPosition	600+0
+Open File for Temperature	
+Activate Temperature:	True
+Cooling Rate (Celcius/second):	2.0
+Heating Rate (Celcius/second):	1.0
+Base Temperature (Celcius):	230.0
+Interface Temperature (Celcius):	230.0
+Object First Layer Infill Temperature (Celcius):	230.0
+Object First Layer Perimeter Temperature (Celcius):	230.0
+Object Next Layers Temperature (Celcius):	230.0
+Support Layers Temperature (Celcius):	225.0
+Supported Layers Temperature (Celcius):	230.0

tower.csv

+Format is tab separated tower settings.
+_Name                          	Value
+WindowPosition	700+0
+Open File for Tower	
+Activate Tower	False
+Extruder Possible Collision Cone Angle (degrees):	60.0
+Maximum Tower Height (layers):	5
+Tower Start Layer (integer):	1